Plastic Ball Bearings all Made in Japan
  • HOME
  • 日本語
  • German
Kashima Bearings, Inc.
  • HOME
  • Products
    • Plastic Ball Bearings
    • Plain Bearings (Bushings)
    • Pillow Blocks (Bearing Units)
    • Processed Plastic Products
  • Applications
    • Applications Depending on Equipment
    • Applications Depending on the Environment
  • Material
    • Phenol
    • PTFE
    • UHMWPE
    • PP
    • PEEK
    • PPS
    • PCTFE
    • Carbon
    • Other Materials
  • Case studies
  • About us
    • Location
    • Plastic Bearing Columns
  • Contact Us
    • FAQ
    • Order flow
    • Inquiry & Download
  • Privacy Policy
  • Products
    • Plastic Ball Bearings
      • Deep-groove Ball Bearings
      • Thrust Ball Bearings
      • Angular-contact Ball Bearings
      • Self-aligning Ball Bearing
      • Miniature Ball Bearings
      • Custom-made Ball Bearings
    • Plain Bearings (Bushings)
    • Pillow Blocks (Bearing Units)
    • Processed Plastic Products
  • Applications
    • Applications Depending on the Environment
    • Applications Depending on Equipment
  • Material
    • Phenol
    • PTFE
    • UHMWPE
    • PP
    • PEEK
    • PPS
    • PCTFE
    • Carbon
    • Other Materials
  • Case studies
  • About us
    • Location
    • Plastic Bearing Columns
  • Contact Us
    • FAQ
    • Order flow
    • Inquiry & Download
Home > About us > Plastic Bearing Columns > What is “Creep” in Plastics?

What is “Creep” in Plastics?

Today, we’ll talk about “creep” in plastic materials.

● Definition

Creep is the phenomenon where a material deforms gradually over time when subjected to a constant load. This is sometimes referred to as cold flow.

There are generally three patterns of creep:

  1. Recovery → When the load is removed, the material partially returns to its original shape depending on its properties.
  2. Permanent deformation → The shape does not return to its original form even after the load is removed.
  3. Fracture → Continuous creep eventually leads to material failure.

Think of it like this:

  • Marshmallow: Deforms when pressed but returns to shape once the pressure is released.
  • Clay: Changes shape under force and stays deformed even after releasing the pressure.
  • Tofu: Deforms at first, but under continuous force eventually breaks apart.
  • (Note: Marshmallows and clay can also eventually break if force is excessive.)

Creep behavior depends on several factors: material type, load, temperature, and time.

Particularly under constant conditions, temperature plays a major role. With identical load and duration, higher temperatures increase creep. This occurs in both plastics and metals, though the degree varies.

Harder materials generally resist creep better, while softer materials are more prone to it (hardness and compressive strength are good indicators).

● Creep Resistance

The higher the creep resistance, the less prone the material is to deformation under long-term load.

Among plastics:

  • Thermosetting resins (such as phenolic or epoxy) generally have better creep resistance than thermoplastics.
  • Among thermoplastics, creep resistance typically follows this order (from highest to lowest):
  • PEEK > PPS > POM > PET > PP > PE > PTFE

■ Creep and Plastic Ball Bearings

In plastic ball bearings, excessive load can cause creep deformation in the raceway grooves where the balls roll.

Unlike wear, this deformation creates uneven surfaces (small dents), which increase rolling resistance and can impair the bearing’s rotation.

This can lead to poor rotation performance and, in severe cases, bearing failure, negatively affecting machine operation.

● Our Approach

In collaboration with a university, we’ve conducted research showing that when pressure is applied to the material of bearing balls, some indentation occurs, but beyond a certain point, deformation stops and does not progress further (unless the load is excessive, causing failure).

Based on this, we are studying the optimal groove geometry (R-profile) of the raceway to minimize creep effects on the rolling balls. Our research aims to define R-shapes tailored to specific materials for improved bearing performance.

For metal bearings, optimal groove geometry ratios relative to ball size are well established from decades of experience. We aim to develop similarly optimized geometries for plastic bearings.

 

Catalogue Downloads

 

Back to Plastic Bearing Columns

About us

  • Location
  • Plastic Bearing Columns
    • Plastics and Electrical Properties (Insulation, Antistatic, Conductivity)
    • Characteristics of PE (Polyethylene)
    • Corrosion Test on Bearings
    • What Are Angular Contact Ball Bearings?
    • Dimensional Changes in Plastics and Processing Methods
    • The Role of Fillers in Plastic Bearings
    • Glass Transition Temperature in Plastics
    • Heat Deflection Temperature (HDT) in Plastics
    • Melting Point and Heat Resistance of Plastics
    • Types of Plastics Based on Tensile, Compressive, and Flexural Strength
    • Thermal Expansion in Plastics
    • Water Absorption in Plastics
    • What Is Weather Resistance in Plastics?
    • What is “Creep” in Plastics?
    • Ball Bearing Precision Grades
    • Friction Coefficient of Plastic Bearings
Catalogue Downloads
ISO

Site Footer

Kashima Bearings, Inc.
  • Home
  • Products
    • Plastic Ball Bearings
    • Plain Bearings (Bushings)
    • Pillow Blocks (Bearing Units)
    • Processed Plastic Products
  • Applications
    • Applications Depending on the Environment
    • Applications Depending on Equipment
  • Material
  • Case studies
  • About us
    • Location
    • Plastic Bearing Columns
  • Contact Us
    • FAQ
    • Order flow
  • Privacy Policy
  • 日本語
  • German
Copyright © 2007-2021 Kashima Bearings All Rights Reserved.
Our website uses cookies to ensure that we give you the best experience on our website. By using this site, you agree to the use of cookies. Accept all cookiesPrivacy Policy